HT PIPE supply all different types and scales of flanges. Please feel free to contact us for further product information and pricing.
ASME B16.48 SS316 1/2" Spectacle Blind flange is a removable pressure boundary assembly used for isolation and flow control in piping systems. It is a disc-shaped part machined from a single sheet metal, containing a "blind disc" and a "spacer ring".
ASME B16.48 SS316 1/2" Spectacle Blind flange Dimensional and Structural Tolerances
ASME B16.48 classifies specifications by nominal diameter (NPS) and pressure class (Class). Common NPS ranges from 1/2" to 48". Pressure classes include Class 150, 300, 600, 900, 1500, and 2500. The core dimensional tolerances for different specifications must meet the following requirements:
Nominal Diameter (NPS) and Nominal Bore: NPS 1/2" corresponds to DN15, NPS 1" corresponds to DN25, and the maximum NPS 48" corresponds to DN1200. Nominal bore deviation must be controlled within ±0.5mm.
Disc Outer Diameter (D): Consistent with the outer diameter of the matching ASME B16.5 flange. For example, the outer diameter of a Class 150 NPS 2" disc is 152.4mm, and that of a Class 300 NPS 2" disc is 165.1mm. Outer diameter tolerances ±0.8mm.
Thickness (T₁) of the blind zone: Designed according to pressure rating, T₁ is 12.7mm for Class 150 NPS 2" and 19.1mm for Class 300 NPS 2", 25.4mm for Class 600 NPS 2", thickness tolerance ±0.8mm, must be verified by the ASME BPVC Section VIII strength formula to ensure no plastic deformation under design pressure.
Orifice zone parameters: Orifice diameter (d) is designed according to flow requirements, commonly ranging from 6mm to the corresponding diameter of NPS (e.g., d=20mm for NPS 2"), orifice diameter tolerance H11 (+0.030mm/0), orifice wall requires a 45° chamfer (depth). (0.5–1 mm) to reduce media erosion, the thickness (T₂) of the throttling orifice area is consistent with that of the fully blind area to avoid uneven stress on the sealing surface.
Bolt hole parameters: The number, hole diameter, and center circle diameter are completely matched with the matching flange. For example, a Class 150 NPS 2" flange corresponds to 4 bolt holes with a hole diameter of 19.1 mm, a center circle diameter of 101.6 mm, and a hole position tolerance of ±0.5 mm to ensure accurate bolt insertion.

stainless steel 316 material
SS316 material must conform to ASTM A182/A182M standards, and the chemical composition must meet the following requirements: Cr 16.0%–18.0%, Ni 10.0%–14.0%, Mo 2.0%–3.0%, C ≤0.08%, Mn ≤2.0%, Si ≤0.75%, P ≤0.045%, S ≤0.03%. The mechanical properties must meet the following requirements: tensile strength ≥515MPa, yield strength ≥205MPa, elongation ≥40%, and Brinell hardness ≤217HB.
Installation Operation Specifications
Pre-installation Inspection: Confirm that the blind flange specifications, material, and operating conditions are compatible. Check that the sealing surface is free of scratches and dents, and that the bolt holes are free of deformation. Verify the specifications and types of the matching flange and gasket.
Installation Steps:
1. Clean the flange sealing surface and the blind flange sealing surface, removing oil and impurities.
2. Place the gasket in the center of the flange sealing surface, ensuring the gasket is not misaligned.
3. Align the blind flange with the flange, aligning the bolt holes with the flange bolt holes, and insert the bolts.
4. Tighten the bolts in a diagonal sequence, with the first tightening torque at 50% of the rated torque, the second at 80%, and the third at 100% (e.g., the rated torque for an M12 bolt is 35 N·m), avoiding uneven stress.
5. After installation, perform a pressure test (test pressure 1.5 times the design pressure), holding the pressure for 30 minutes without leakage.
Switching Operation Precautions: Before switching, close the pipeline valves and depressurize to below 0.1 MPa. Use opposite bolts as the rotation axis to prevent the blind plate from falling off. When rotating the blind plate, operate slowly to ensure that there is no friction damage between the sealing surface and the gasket. After switching, retighten the bolts and check the sealing performance again.
Frequently Asked Questions (FAQ)
What is the difference between an ASME B16.48 spectacle blind and an ASME B16.5 blind flange?
An ASME B16.5 blind flange is a solid bolted disc used to permanently cap the very end of a pipe run. An ASME B16.48 spectacle blind is sandwiched directly between two active lines and can be rotated easily to switch a pipe section from a full-flow state to an absolute blanked state without dismantling the piping assembly.
Why are 1/2" spectacle blinds thicker than standard steel plates?
Because a spectacle blind must absorb the entire pressure differential of an isolated piping system without bending or flexing. ASME B16.48 outlines strict calculation equations ensuring the thickness can safely withstand the maximum hydro-test and operational pressures of that specific class line.
Can these blinds be supplied with a lifting hook or pre-drilled handle hole?
Yes. Standard 1/2 inch configurations come with a pre-drilled hole in the center connector web, designed to slide over a flange bolt to simplify alignment and rotation on-site.
Why Choose Us?
- EN 10204/3.1B
- Raw Materials Certificate
- 100% Radiography Test Report
- SGS Third Party Inspection Report, etc
- Huge Stock, Timely delivery
- Free Quote, Inquiry answered within 24 hours
HT PIPE is a well-known stockist and exporter. We are a ss316 supplier with 15+ export experience. We not only provide pipes, plate, round bars, but also pipe fittings, flanges, etc. Contact us for more information and prices for free.





