F51, F53, F55, F60 and F61 Supplier manufacturer, contact us to get free quote and sample!
Our company is a professional one-stop service manufacturer supplier. Not only provide duplex steel pipe fittings, but also provide Super Duplex 2507 Pipe, plates, sheets, round bars, etc. Free samples can be provided. Please contact us for a free quotation.
Key Differences: F51 vs F53 vs F55 vs F60 vs F61
All five are ASTM A182 forged duplex grades, and all five are ordered as flanges, fittings and valve bodies. What separates them is how much chromium, molybdenum, nitrogen and copper sits in the alloy, and that single number - the pitting resistance equivalent, PREN - is what decides whether the part survives the medium. Start with the duty, not with the grade name.
| If the duty is | Specify | Because |
|---|---|---|
| Seawater, chlorides, general chemical and offshore piping at moderate pressure | F51 (S31803) or F60 (S32205) | Standard 2205 duplex, PREN 32-34, the lowest cost option that still beats 316L by a wide margin |
| High chloride plus high pressure, or wall thickness reduction wanted on a load bearing line | F53 (S32750) | Super duplex, PREN 40.5 minimum and 550 MPa minimum yield, so the same pressure is carried on a thinner wall |
| Sour service with CO2 and H2S, heavy section welding, or seawater injection lines | F55 (S32760) | Zeron 100 type with tungsten and copper, PREN 40 plus better resistance to crevice attack in chlorinated seawater |
| Pump and valve trim, shafts, or anywhere the highest strength with copper alloying is the driver | F61 (S32550) | Ferralium 255 type, copper bearing, 550 MPa minimum yield with the highest pitting resistance of the five |
One trap catches a lot of buyers: F51 and F60 are not two different alloys. F51 is the older UNS S31803 composition, F60 is UNS S32205, the tightened version of the same 2205 grade that pushes chromium, molybdenum and nitrogen to the upper half of the range. A heat that meets S32205 can be dual certified as S31803, but a heat that only meets S31803 cannot be sold as S32205. If the enquiry says F60, do not substitute F51 plate and hope the certificate passes.
Composition and PREN Side by Side
PREN is calculated as Cr + 3.3 Mo + 16 N, with tungsten and copper added in some specifications for the super duplex grades. It is the fastest way to compare two certificates without running a corrosion test.
| Grade | UNS | Cr | Ni | Mo | N | Cu / W | PREN |
|---|---|---|---|---|---|---|---|
| F51 | S31803 | 21.0 - 23.0 | 4.5 - 6.5 | 2.5 - 3.5 | 0.08 - 0.20 | - | 32 - 33 |
| F60 | S32205 | 22.0 - 23.0 | 4.5 - 6.5 | 3.0 - 3.5 | 0.14 - 0.20 | - | 34 min |
| F53 | S32750 | 24.0 - 26.0 | 6.0 - 8.0 | 3.0 - 5.0 | 0.24 - 0.32 | - | 40.5 min |
| F55 | S32760 | 24.0 - 26.0 | 6.0 - 8.0 | 3.0 - 4.0 | 0.20 - 0.30 | Cu 0.5 - 1.0 / W 0.5 - 1.0 | 40 min |
| F61 | S32550 | 24.0 - 27.0 | 4.5 - 6.5 | 2.9 - 3.9 | 0.10 - 0.25 | Cu 1.5 - 2.5 | 40 min |
Strength: Why Super Duplex Lets You Drop a Wall Size
The minimum room temperature properties below are the A182 acceptance values for solution annealed forgings. They matter commercially, not just technically: at 550 MPa minimum yield against 450 for standard duplex, a super duplex flange can often be specified one pressure class lighter for the same duty.
| Grade | Tensile strength [MPa] | 0.2% yield [MPa] | Elongation [%] | Class |
|---|---|---|---|---|
| F51 | 620 min | 450 min | 25 min | Duplex |
| F60 | 655 min | 450 min | 25 min | Duplex |
| F53 | 800 min | 550 min | 15 min | Super duplex |
| F55 | 750 min | 550 min | 25 min | Super duplex |
| F61 | 760 min | 550 min | 15 min | Super duplex |
Read the elongation column as well. F53 and F61 give up ductility to reach that strength, so they are a poor choice for parts that get cold formed or heavily machined after forging. F55 keeps 25% elongation at the same 550 MPa yield, which is one reason it is preferred for complex fittings and heavy section welds.
Application Guide: Which A182 Grade to Specify
Chemical and petrochemical lines on chlorinated cooling water: F51 or F60, and move to F53 only where pitting has actually been a problem. Offshore topside piping and seawater systems: F53 for the small bore high pressure runs, F55 where welds are thick and sour service is on the datasheet. Desalination and seawater injection: F55, because crevice corrosion in chlorinated seawater is the failure mode that kills standard duplex. Pump casings, impellers and valve trim: F61, where the copper addition and the higher strength both earn their cost.
Product data for the pipe side of the same grades is on our 2205 duplex pipe page and the Super Duplex 2507 pipe page, with the full flange and fitting range on the duplex stainless steel pipe category.
ASTM A182 F51 (UNS S31803 / S32205):
Duplex Stainless Steel:
Balanced combination of ferritic and austenitic phases.
Chemical Composition:
Chromium (Cr): 21.0–23.0%
Nickel (Ni): 4.5–6.5%
Molybdenum (Mo): 2.5–3.5%
Nitrogen (N): 0.08–0.20%
Applications: Chemical processing, oil and gas, marine engineering.
Note: Can be dual-certified as S32205 but not vice versa.
ASTM A182 F53 (UNS S32750):
Super Duplex Stainless Steel:
Enhanced corrosion resistance. Increased chromium content compared with F51 for improved pitting corrosion resistance. Higher yield strength allows for reducing section size in load-bearing applications.
Chemical Composition:
Chromium (Cr): 24.0–26.0%
Nickel (Ni): 6.0–8.0%
Molybdenum (Mo): 3.0–5.0%
Applications: Suited for aggressive corrosive environments.
Note: Higher yield strength than F51.
ASTM A182 F55 (UNS S32760):
Super Duplex Stainless Steel:
Contains tungsten in addition to chromium and nickel.
Chemical Composition:
Chromium (Cr): 24.0–26.0%
Nickel (Ni): 6.0–8.0%
Molybdenum (Mo): 3.0–4.0%
Applications: Chemical processing, marine engineering.
Note: Known as Zeron 100; high strength and corrosion resistance.
ASTM A182 F60 (UNS S32205):
Duplex Stainless Steel:
Balanced combination of strength and corrosion resistance. Manufacturers optimised the UNS S31803 composition towards the top end of the limits to improve pitting corrosion resistance. This grade, with a tighter specification, is captioned as F60, equating to UNS S32205.
Chemical Composition:
Chromium (Cr): 21.0–23.0%
Nickel (Ni): 4.5–6.5%
Molybdenum (Mo): 2.5–3.5%
Nitrogen (N): 0.14–0.20%
Applications: Chemical, petrochemical, and offshore industries.
ASTM A182 F61 (UNS S32550):
High-Alloy Stainless Steel:
Known as Ferralium 255; the original super duplex stainless steel.
Chemical Composition:
Specific composition with added copper for improved pitting corrosion resistance.
Applications: Wide range of demanding applications.
Note: Offers increased strength and corrosion performance compared to F53 and F55.
When selecting between these grades, considerations should be based on specific application requirements, environmental conditions, and desired material properties. It's advisable to consult with materials engineers or industry experts to ensure the most suitable choice for a particular application. Contact us for free more information and prices!





