Most nickel alloys are sold on a number. For alloy 400 that number is 63, the minimum nickel content in ASTM B127, and the alloy it describes is the only commercially significant nickel-copper grade in the world. It has been in service since the early twentieth century, it is the default material for hydrofluoric acid, and it will fail faster than 304 stainless steel in a nitric acid line.
That last sentence is the reason this grade deserves a careful article rather than a data sheet. Monel 400 plate is bought in large quantities by chemical plants, desalination contractors, offshore fabricators and salt producers, and almost every expensive mistake made with it comes from assuming that a high-nickel alloy must be good everywhere. It is not. It is excellent in a narrow set of reducing and neutral chloride environments, and it is poor in oxidizing acid. The boundary is sharp, it is well documented, and it can be drawn precisely.
The alloy in one paragraph
Alloy 400 is a single-phase solid-solution nickel-copper alloy, roughly 65 percent nickel and 30 percent copper in practice, with small iron and manganese additions. Because it has no precipitation-hardening mechanism and no significant carbide reaction, it cannot be strengthened by heat treatment at all. The only strengthening route is cold work, and that single fact explains the temper structure of B127, the welding behaviour, and the reason the annealed condition is both the weakest and the most corrosion-resistant form of the product.
It also explains why the grade is often delivered without a final heat treatment. A plate that is annealed and then lightly rolled will be stronger than an annealed plate and almost as resistant, and fabricators routinely buy in that condition to save a stress-relief operation. That is a legitimate commercial choice, and it must be declared on the order, because "Monel 400 plate" without a temper is an incomplete specification.
Chemistry under ASTM B127
| Element | B127 limit, % | Nominal, % | Why it matters |
| Ni + Co | 63.0 min | 65.0 | Reducing-environment resistance, chloride SCC immunity, austenite stability |
| Cu | 28.0 – 34.0 | 30.0 | Seawater performance, HF resistance, thermal conductivity |
| Fe | 2.5 max | 1.0 | Residual from melting; kept low for seawater and HF duty |
| Mn | 2.0 max | 0.5 | Deoxidation and desulphurisation |
| C | 0.30 max | 0.10 | Generous by nickel alloy standards; no carbide sensitisation issue |
| Si | 0.50 max | 0.25 | Deoxidation |
| S | 0.024 max | 0.005 | Weld soundness; sulphur also embrittles during annealing |
Two lines of that table deserve comment because they differ from what buyers expect after working with Inconel grades. Carbon at 0.30 percent is loose, roughly six times the ceiling on alloy 690, and it is loose for a good reason: 400 does not form a continuous grain-boundary carbide network that would sensitise it, so carbon is not the corrosion variable here. Sulphur at 0.024 percent is tight, and it is tight for a different reason: this alloy is genuinely sensitive to sulphur at annealing temperature, and a sulphur-bearing furnace atmosphere will embrittle the plate.
The iron ceiling matters more than its number suggests. Iron is a residual that enters through scrap and through the melting practice, and it degrades performance in exactly the two environments the alloy is bought for. In seawater it can promote preferential attack; in hydrofluoric acid it dilutes the nickel-copper matrix that gives the grade its resistance. A certificate showing 2.4 percent iron is technically compliant and commercially inferior to one showing 0.9 percent.
The three temper rows that decide acceptance
B127 specifies minimum mechanical properties by condition, and the differences are large enough that quoting a single set of numbers is misleading. The three rows below are the specified minima for plate, sheet and strip.
| Condition | 0.2 % proof stress | Tensile strength | Elongation | Where it is used |
| As hot rolled | 275 MPa | 515 MPa | 25 % | Vessel shells, general plate work, no forming after delivery |
| Annealed | 195 MPa | 485 MPa | 35 % | Formed heads, dished ends, linings that must be bent or rolled |
| Hard (cold rolled) | 620 MPa | 690 MPa | 2 % | Gaskets, wear parts, structural blanks needing strength without heat treatment |
The annealed row is the one that catches people out. A yield strength of 195 MPa is low, lower than 304 stainless in the annealed condition, and a fabricator who designs a 400 vessel on "nickel alloy" assumptions without checking the temper will produce something that deflects twice as much as expected. Alloy 400 is a corrosion material, not a structural one, in its annealed state. If the design needs strength, the answer is a temper or a different alloy, not a thicker plate in the annealed condition.
The hard-temper row shows the opposite extreme: 620 MPa proof stress with 2 percent elongation is a different material in mechanical terms, and it is not suitable for anything that will be formed, bent or subject to thermal cycling. Selling hard-temper plate into a lining application because it was cheaper per kilogram is a classic substitution error.
Typical mill results sit above the minima. An annealed plate commonly reports around 240 MPa proof, 520 MPa tensile and 45 percent elongation, which gives a useful margin over the specification. The gap between 195 MPa minimum and 240 MPa typical is the fabrication allowance the designer should not spend.
Plate, sheet and strip: the boundary and the overlap
B127 covers all three flat-product forms in one document, and the boundary between them is defined by thickness, with width as a second discriminator in the overlap band. Plate begins at 4.76 mm (0.188 in) and runs upward; sheet occupies roughly 0.46 mm to 6.4 mm; strip and coil start as thin as 0.13 mm.
The overlap between 4.76 and 6.4 mm is the part that causes disputes. A 5 mm item is thick enough to be plate and thin enough to be sheet, and which document requirement applies depends on the width and on the mill's product route. The practical rule is to specify thickness, width, length and temper together, and to name the product class you expect. A purchase order that says "5 mm Monel 400 sheet, 1,500 mm wide" is ambiguous, and a mill is entitled to quote either route.
This matters because the tolerances differ. Plate thickness tolerance is coarser than sheet tolerance, and a fabricator planning a machined flange from 5 mm stock will lose the machining allowance if the plate arrives at the bottom of a plate tolerance band. Name the class, and name the tolerance table.
Physical properties that drive the design
| Property | Value | Design consequence |
| Density | 8.83 g/cm³ | About 10 % heavier than 316L for the same volume; affects crane and freight planning |
| Melting range | 1,300 – 1,350 °C | Lower than the nickel-chromium grades; weld procedures must reflect it |
| Modulus of elasticity | Approximately 180 GPa | Lower than steel; deflection calculations must use this figure, not 200 GPa |
| Thermal conductivity at 20 °C | Approximately 21.8 W/m·K | Roughly five times 316L; heat travels along the plate and into fixtures during welding |
| Thermal expansion, 20 – 100 °C | Approximately 13.9 µm/m·K | Lower than austenitic stainless; dissimilar joints move less than expected |
| Curie temperature | Close to room temperature | Some heats are faintly magnetic at ambient and lose it on heating; do not use magnetism as an identification test |
| Strengthening route | Cold work only | No age hardening, no precipitation treatment, no post-weld strength recovery |
The magnetic line has practical consequences beyond identification. A fabricator who tests incoming plate with a magnet and rejects a slightly magnetic heat as "contaminated" is rejecting compliant material. Composition variation moves the Curie temperature around ambient, so a faint attraction at room temperature is normal and does not indicate free iron.
The thermal conductivity line is the one that shows up in the weld shop. At roughly 21.8 W/m·K the alloy conducts heat about five times as readily as austenitic stainless, so heat drains into the surrounding plate and into the fixture, and weld penetration comes out shallower than the same procedure would produce on 316L. Procedures transferred from stainless without increasing amperage produce lack of fusion at the root, and that defect is invisible from the outside.
Hydrofluoric acid: the service this alloy owns
Alloy 400 is one of a very small number of metallic materials that will handle hydrofluoric acid across the concentration range, including the anhydrous and aqueous forms used in alkylation and in acid production, and it is the default material for that duty in the chemical process industry. The reason is electrochemical rather than mechanical: in HF the alloy forms a protective fluoride film that is stable enough to keep the corrosion rate low, while most stainless steels and most nickel alloys either pit or general-corrode.
The commercial consequence is a specific equipment list. HF alkylation unit reactors, acid settlers, acid storage tanks, acid coolers, and the piping and vessel linings around them are built from 400 plate. So are the vessels in HF production where anhydrous acid is handled. In these services the plate is usually supplied annealed and pickled, formed into shells and heads, and welded with matching nickel-copper filler.
Two boundary conditions apply even here. First, HF service with residual oxygen or with oxidizing species shifts the environment and can attack the alloy at rates that the pure-acid data does not predict; the corrosion charts are drawn for air-free acid and they say so. Second, the alloy's advantage is in the metal, not in the joint: a weld that is diluted with iron from poor fit-up, or a heat-affected zone left with scale, becomes the weak point in an otherwise correct fabrication.
Seawater and brackish water: flowing versus stagnant
The marine reputation of alloy 400 is genuine and it is conditional. In fast-flowing, aerated seawater the alloy performs extremely well, with corrosion rates low enough that the material is used for pump shafts, impellers, propeller shafts, water boxes, condenser plates and splash-zone lining on offshore structures. The flow matters: moving seawater keeps the surface oxygenated and prevents the deposits that create crevices.
Under deposits, in stagnant pockets, and in the gaps between a plate lining and its backing structure, the environment becomes deaerated and the alloy's behaviour changes. chloride pitting and crevice attack become possible, and a lining that is not fully bonded or that has a stagnant gap behind it will show attack on the plate back face within a few years. Design details, not material selection, decide whether a seawater lining survives: drain the gap, vent it, or bond it fully.
The comparison that matters commercially is against the copper-nickel alloys. 90-10 and 70-30 cupronickel are cheaper and are the standard choice for large seawater piping and condenser tube bundles, where their resistance to flowing seawater is adequate and their cost per square metre is decisive. Alloy 400 wins where the flow is high, where erosion-corrosion would remove cupronickel, where chlorides are combined with acid, and where a single material must handle both seawater and a chemical stream.
Velocity is the practical selection variable. Cupronickel has a documented velocity ceiling above which erosion-corrosion accelerates; alloy 400 tolerates higher velocities and is chosen for impellers and pump casings for exactly that reason. A seawater system that has already destroyed a cupronickel impeller is a system that should be quoting 400.
Sulphuric and hydrochloric acid: the concentration windows
| Acid | Documented window for alloy 400 | Boundary condition |
| Sulphuric acid | Up to about 80 % concentration at room temperature; about 15 % at boiling | Air-free, unaerated acid. Aeration raises the corrosion rate sharply |
| Hydrochloric acid | Up to about 10 % concentration at room temperature | Aerated acid, cold. Seldom the material of choice above that |
| Hydrofluoric acid | Broadly across concentrations | Air-free. The defining application for the grade |
| Nitric and nitrous acid | Not suitable | Strongly oxidising; the alloy corrodes rapidly. This is 304L, 310 or 690 territory |
Those windows are narrow and they are temperature-dependent, and the failure mode when they are exceeded is general corrosion rather than a localised pit, which is at least predictable. The dangerous case is a process that starts inside the window and drifts: a sulphuric acid stream that is aerated by a leaking pump seal, or a batch that runs hotter than the design case, will move the alloy from acceptable to unacceptable without any visible change on the drawing.
This is why the acid service data for alloy 400 is always published as an isocorrosion chart with aerated and air-free lines drawn separately. A procurement engineer who quotes "resistant to sulphuric acid" without the concentration, temperature and aeration state has quoted nothing usable.
Where the alloy genuinely fails
| Environment | Behaviour | Note |
| Nitric acid, nitrous acid | Rapid attack | Oxidising acids are the alloy's fundamental weakness; no workaround exists |
| Caustic at high temperature, high stress, high concentration | Caustic stress-corrosion cracking possible | The alloy resists caustic corrosion well but is not immune to caustic SCC; stress relief matters |
| Sulphur-bearing gases above about 371 °C | Attack | Nickel sulphide formation; limits high-temperature service in sulphur-containing atmospheres |
| Molten sulphur above about 260 °C | Attack | Relevant to sulphur handling and to some refinery duties |
| Ammonia and ammoniacal systems | Case-dependent, often poor | Evaluate per duty; do not assume the high nickel content protects anhydrous or aqueous ammonia service |
| Aerated or oxidising acid streams | Accelerated general corrosion | The isocorrosion charts separate air-free from aerated for this reason |
| Stagnant seawater behind a lining | Crevice and pitting attack | Design the drainage and venting, not just the material |
Read this table next to the successes and the alloy becomes predictable. It is a reducing-environment and chloride material with a hard ceiling at oxidising chemistry. Every field failure that is not a fabrication defect falls into one of those rows.
The caustic SCC row is the subtle one, because the marketing language around 400 emphasises hot caustic resistance and stops there. The alloy does resist caustic corrosion well, and it is used for caustic evaporators and storage. But high concentration combined with high temperature and residual stress has produced caustic SCC in service, and the remedy is a stress-relief treatment on formed and welded components rather than a change of grade.
Heat treatment: a soft anneal and a sulphur warning
The anneal for alloy 400 is a low-temperature operation by nickel alloy standards: roughly 760 to 980 °C for a short time at temperature, followed by cooling. Its purpose is to soften cold-worked material and restore ductility while keeping a reasonably fine grain size, and it is a recrystallisation anneal rather than a solution treatment.
The furnace atmosphere is the part that matters and the part that is usually omitted from purchase documents. Sulphur compounds in the furnace atmosphere embrittle this alloy during exposure at annealing temperature, and the embrittlement is not visible in a tensile test at room temperature. A heat treater running nickel alloys and sulphur-bearing steels through the same furnace without atmosphere control will produce compliant-looking plate with poor ductility at the grain boundaries.
For cold-deformed plate that needs stress relief rather than full softening, a low-temperature treatment around 300 °C for one to three hours is sufficient and does not disturb the temper. That is the correct answer for a formed head or a rolled shell that needs its residual stress reduced before entering caustic or HF service, and it is much cheaper than a full anneal.
The commercial reality is that a large share of 400 plate goes into service with no final heat treatment at all, deliberately, to retain the strength from the last rolling pass. That is legitimate where the component is not formed after delivery and where the corrosion duty does not require maximum ductility. It is not legitimate for a dished head or a U-bend.
Welding: matching filler and a sluggish pool
The matching consumables are ERNiCu-7 wire and ENiCu-7 covered electrodes. No preheat is required and no post-weld heat treatment is normally applied, which makes the alloy attractive for site fabrication. What is not attractive is the welding behaviour, and it has two specific causes.
- The molten pool is sluggish. It does not flow out and wet the joint the way stainless does, so the joint preparation must be opened up enough to let the filler reach the root. A joint designed on stainless practice will bridge and leave a root defect.
- Penetration is shallower because the thermal conductivity is high and the heat is conducted away from the pool. Increasing amperage is the usual remedy, but the alloy also has a lower melting range than the nickel-chromium grades, so the window between "enough penetration" and "burn-through" is narrower than it looks.
- Joint cleanliness is critical. Lubricants, paint, marking fluids and scale all introduce sulphur, lead or other embrittling elements into a weld that has no post-weld treatment to repair the damage.
- For lining work, plug welds and stitch welds must be planned so that no stagnant gap remains behind the plate; the weld pattern is a corrosion design decision, not just a fixing detail.
- Dissimilar joints to carbon steel or stainless are common in lined vessels and nozzles. The nickel-copper filler is compatible with both, but the carbon-steel side needs its own procedure qualification.
The most expensive welding error on this grade is dilution. A root pass that melts a large volume of carbon steel backing or of stainless nozzle stock pulls iron and chromium into the nickel-copper deposit, and the resulting weld is neither 400 nor stainless, with corrosion resistance worse than either. Fit-up and backing design should be treated as part of the corrosion specification.
Forming and machining
Cold forming is one of the alloy's better properties. Its work-hardening rate is lower than 304 or 301 stainless, which means it can take multiple draw operations with fewer intermediate anneals, and it is routinely rolled, dished, spun and pressed on standard shop equipment.
Springback is moderate and predictable, but the low annealed yield strength means a formed part has little resistance to deformation during handling. Large dished heads need supporting and are usually stress relieved before installation for that reason as much as for corrosion.
Machining is described in the trade literature as good, and it is better than the nickel-chromium alloys, but it is not free-cutting. The alloy is ductile and gummy, it work-hardens under a dull tool, and it has a built-in tendency to drag and to produce built-up edges.
Sharp positive-rake carbide, generous feed per revolution, and a depth of cut below the work-hardened skin are the standard approach. The free-machining variant of this family is Monel R-405, which carries added sulphur specifically to break chips; it is a different grade with different corrosion limits and should not be substituted silently.
Cutting plate is normally plasma, water jet or shear. Plasma leaves a heat-affected edge that should be dressed back before the part enters HF or seawater service, and water jet avoids the thermal issue entirely. Sheared edges on thick plate carry cold work and micro-cracks, and a sheared edge in a caustic or HF vessel should be machined or ground before service.
Metre weight: the number that sets the quotation
Nickel-copper plate is priced by weight, and the copper content means the price moves with the copper market in a way that stainless does not. Being able to compute the mass of a blank quickly is therefore a commercial skill, not just an engineering one.
Mass per square metre (kg/m²) = thickness in mm × 8.83
| Thickness, mm | Mass per m², kg | Typical use |
| 3 | 26.5 | Thin lining, ducting, baffles |
| 4 | 35.3 | Lining sheet, small vessel shells |
| 5 | 44.2 | Lining, light shells, gasket blanks |
| 6 | 53.0 | Vessel shell and lining plate |
| 8 | 70.6 | Shell plate, tube sheet blanks |
| 10 | 88.3 | Pressure shell, flange blanks |
| 12 | 106.0 | Tube sheet, heavy shell |
| 16 | 141.3 | Tube sheet, heavy components |
| 20 | 176.6 | Tube sheet, structural plate |
| 25 | 220.8 | Heavy tube sheet, machined parts |
| 30 | 264.9 | Heavy pressure parts |
| 40 | 353.2 | Large tube sheets, thick sections |
| 50 | 441.5 | Heavy plate work |
A 6 mm × 1,500 mm × 1,500 mm lining blank weighs 11.9 kg. The same blank in 316L at 8.0 g/cm³ weighs 10.8 kg, so the nickel-copper plate is about ten percent heavier for the same thickness. That ten percent is never the deciding factor in a lining project; the alloy price per kilogram, which is roughly four to six times the stainless price, is the deciding factor. Compute the mass for the freight, and negotiate the alloy content for the price.
Substitution traps in this grade family
| Grade | What it is | Why it gets substituted | What breaks |
| Monel 400 (N04400) | Nickel-copper solid solution | Reference grade | - |
| Monel R-405 | Free-machining variant with added sulphur | Easier to machine | Corrosion resistance and weldability are lower; not interchangeable for HF or seawater plate |
| Monel K500 (N05500) | Age-hardenable nickel-copper with aluminium and titanium | Much higher strength, similar name | Different heat treatment, different welding, different procurement document; a K500 order is not a 400 order |
| Alloy 825 (N08825) | Nickel-iron-chromium with molybdenum and copper | Broader acid coverage | Better in sulphuric and phosphoric acid, but not equivalent in HF; also a different price level |
| Cupronickel 90-10 / 70-30 | Copper-base alloys | Cheaper for seawater | Lower velocity tolerance, no HF capability, weaker at higher temperature |
| Nickel 200 (N02200) | Commercially pure nickel | Similar in caustic | Better in caustic, worse in seawater and in reducing acid with chlorides; not a drop-in |
The K500 substitution is the one that causes the most trouble, because the two grades share a family name and a colour, and a purchasing department searching for "Monel plate" will find both. K500 is strengthened by precipitation of a nickel-titanium-aluminide phase, so it needs a specific aging treatment and it welds differently, and its corrosion resistance in some media differs from 400. Ordering K500 where 400 was specified because it was in stock is a documented route to a failed vessel.
Purchase specification checklist
| Item | What to write on the order |
| Specification | ASTM B127 / ASME SB-127 plate, sheet and strip, with the revision year |
| Grade | UNS N04400, alloy 400, W.Nr. 2.4360; state explicitly that K500 and R-405 are not acceptable |
| Temper | Annealed, as hot rolled, or a named cold-rolled temper; never leave the temper unstated |
| Dimensions | Thickness, width, length in millimetres, plus the tolerance table and the product class (plate or sheet) |
| Chemistry | Ni 63.0 min, Cu 28.0–34.0, C 0.30 max, S 0.024 max, and an iron ceiling tighter than 2.5 % if the duty is HF or seawater |
| Mechanical | The B127 row for the ordered temper, tested per heat, with elongation reported |
| Surface | Hot rolled and pickled, or cold rolled; state finish and any pit or inclusion limits |
| Edge condition | Sheared, machined, or plasma cut with the heat-affected zone dressed back |
| Flatness | Specify flatness tolerance where the plate will be machined or used as a tube sheet |
| Heat treatment record | Furnace atmosphere declared as low-sulphur, with temperature and time reported |
| Testing | Chemical analysis, tensile per heat, hardness where a temper is ordered, and any PMI requirement |
| Documentation | EN 10204 3.1 mill test certificate with heat number, plus dimensional inspection report |
| Marking | Grade, UNS number, heat number, size and temper on each plate, legible after cutting |
Alloy 400 is bought for one thing: the ability to sit in a reducing, chloride-bearing environment, including hydrofluoric acid, for twenty years without thinning. The 63 percent nickel and 30 percent copper buy exactly that, and they buy nothing at all in an oxidising acid. Specify the grade against the medium, specify the temper against the forming route, and specify the sulphur control in the furnace against the ductility the fabrication depends on.





