Duplex 2205 Prefabricated Pipe Spools

Duplex 2205 Prefabricated Pipe Spools


1. Customized Prefabrication Pipe Spools
2. Pipe welded with Flanges
3. Pipe welded with Fittings
4. Flanges welded with Fittings
Send Inquiry
Product Introduction

Duplex 2205 Prefabricated Pipe Spools: Material, Welding and Delivery Scope

A prefabricated 2205 spool is not simply a length of duplex pipe with flanges welded on. The alloy sets hard limits on how the shop heats, welds, tests and documents the assembly, and those limits are the difference between a spool that passes site inspection and one that is rejected at the gate. This page covers what a 2205 spool actually consists of and what has to be on the paperwork.

 

The Material Behind the Spool

Duplex 2205, UNS S32205, sits at roughly 22 percent chromium, 5 percent nickel, 3 percent molybdenum and 0.15 percent nitrogen. The nitrogen is what gives the grade its strength after welding: it raises the yield strength to a 450 MPa minimum and stabilises the austenite-ferrite balance in the weld metal, which is where ordinary 316 tends to lose corrosion resistance.

 

The annealed mechanical minimums are 450 MPa yield, 620 MPa tensile and 25 percent elongation. The pitting resistance equivalent number lands above 34, which is the practical reason 2205 replaces 316L in chloride service rather than simply being a stronger steel.

 

Element UNS S32205 range (%)
Chromium 22.0 - 23.0
Nickel 4.5 - 6.5
Molybdenum 3.0 - 3.5
Nitrogen 0.14 - 0.20
Carbon 0.030 max
PREN 34 min

 

Which Standards Govern Each Part of the Spool

A spool crosses three specifications at once, and each covers a different component: the pipe body, the fittings, and the fabrication itself. Buyers who quote only one of them usually end up with a certificate that does not match the drawing.

 

Component Specification
Seamless or welded pipe ASTM A790 / ASME SA-790 (S32205)
Butt-weld fittings and elbows ASTM A815 / ASME SA-815 (WPS 32205)
Flanges ASTM A182 / ASME SA-182 F51
Fabrication and welding ASME B31.3 process piping
Plate used for any formed part ASTM A240 / ASME SA-240

 

2205 prefabrication pipe of spools

Welding Rules That Cannot Be Relaxed

Duplex is less forgiving than austenitic stainless in the weld. Three parameters decide whether the joint keeps its corrosion resistance:

 

  • Heat input is kept in a narrow band, typically 1 to 2 kJ per mm for the root and fill passes. Too low and the ferrite content runs high; too high and the nitrogen is lost and the weld turns brittle.
  • Interpass temperature is held below roughly 150 degrees C. Waiting between passes costs time and is the single most skipped step on a shop floor.
  • Filler metal matches the parent grade, usually ER2594 or ER2209, and the root is purged with argon. An unpurged root leaves an oxidised layer that fails a pickling test every time.

 

After welding, the joint is brushed and pickled or electro-polished. Skipping this step does not show up in a dimensional check, but it does show up as early pitting in service.

Size Range and What a Spool Drawing Has to State

Spools are built to the isometric, so the drawing rather than the catalogue sets the dimensions. The shop capability that matters is the envelope it can handle:

 

Parameter Typical shop capability
Nominal size DN15 to DN600 (1/2 inch to 24 inch)
Wall thickness SCH10 to SCH160, plus custom heavy wall
Single spool length up to 12 m, limited by transport
Flange rating CL150 to CL1500, RF or RTJ facing
Fit-up tolerance plus or minus 1.5 mm on centre-to-centre

 

A drawing that gives only the bore and the flange standard will come back with a query. What the shop needs is: centre-to-centre dimensions, flange facing and rating, gasket surface finish, whether the spool is to be stress relieved, the test pressure, and the NDT extent.

 

Inspection and Documents Supplied With the Spool

Every spool leaves with a document pack, and the pack is what the site inspector reads before the spool goes into the rack:

 

  • Mill certificates for pipe, fittings and flanges, EN 10204 3.1, traceable to heat numbers marked on the spool.
  • Welder qualification records and the WPS/PQR that the joint was made to.
  • Radiography or ultrasonic report for the weld, with the acceptance level stated (B31.3 normal or severe).
  • Dimensional report against the isometric, including flange face parallelism and bolt-hole alignment.
  • Pickling or passivation record, and a ferrite check on the weld if the specification calls for one.

 

Where 2205 Spools Are Used

The grade is chosen where chlorides and moderate temperature meet: desalination trains, seawater cooling circuits, chemical tanker unloading lines, pulp mill bleach plants, and flue gas desulphurisation piping. In all of these the spool is doing the same job, carrying a chloride-bearing stream that would pit 316L within a few campaigns.

 

Above roughly 60 degrees C in concentrated chloride service the decision usually moves to super duplex 2507, and in strong reducing acid it moves to a nickel alloy instead. 2205 is the middle of that range, not the top of it.

 

FAQ

Q: About Duplex 2205 Prefabricated Pipe Spools price per kg?

A: Prices ranges from $25 to $40 per kg, vary depending on size, wall thickness, supplier etc.

Q: How long does your delivery time take?

A: Delivery time is within 5-21 days

Q: Is There Sample Service?

A: Samples Are Provided Free Of Charge

Q: What Is The Minimum Order Quantity?

A: No Minimum Order Quantity

Q: How to pack the products?

A: The inner layer has a waterproof paper outer layer and is fixed with a fumigation wooden pallet.

Q: Exported Countries

A: Brazil, South Africa, Indonesia, India, Singapore, Malaysia, Iran, Russia, UAE, Chile, Laos, etc

 

 

Hot Tags: duplex 2205 pipe spool, 2205 prefabricated pipe spool, UNS S32205 spool, ASME B31.3 pipe spool fabrication, duplex stainless pipe spool supplier, 2205 spool with flanges, fabricated pipe spools, flanged fittings, flanged pipe, pipe with flange, Pre Fabrication Pipe Spools, stainless pipe flanges

Send Inquiry

whatsapp

Phone

E-mail

Inquiry